? semiconductor components industries, llc, 2000 march, 2000 rev. 6 1 publication order number: mc10h602/d
the mc10h/100h602 is a 9bit, dual supply ttl to ecl translator with latch. devices in the motorola 9bit translator series utilize the 28lead plcc for optimal power pinning, signal flowthrough and electrical performance. the h602 features dtype latches. latching is controlled by latch enable (len), while the master reset input resets the latches. a postlatch logic enable is also provided (enecl), allowing control of the output state without destroying latch data. all control inputs are ecl level. the 10h version is compatible with mecl 10h ecl logic levels. the 100h version is compatible with 100k levels. ? 9bit ideal for byteparity applications ? flowthrough configuration ? extra ttl and ecl power/ground pins to minimize switching noise ? dual supply ? 3.5 ns max d to q ? pnp ttl inputs for low loading logic symbol dq en dq en dq en dq en dq en dq en dq en dq en dq en enecl d0 d1 d2 d3 d4 d5 d6 d7 d8 len mr q0 q1 q2 q3 q4 q5 q6 q7 q8 ttl ecl d l h x x x truth table len l l h x x mr l l l h x q l h q 0 l l enecl h h h h l http://onsemi.com device package shipping ordering information mc10h602fn plcc28 37 units/rail marking diagram a = assembly location wl = wafer lot yy = year ww = work week plcc28 fn suffix case 776 10h602 awlyyww 1 pinout: 28lead plcc (top view) pin names pin function gnd v cce v cco v cct v ee d0 d8 q0 q8 enecl len mr ttl ground (0 v) ecl v cc (0 v) ecl v cc (0 v) e outputs ttl supply (+ 5.0 v) ecl supply ( 5.2 / 4.5 v) data inputs (ttl) data outputs (ecl) enable control (ecl) latch enable (ecl) master reset (ecl) d6 567891011 25 24 23 22 21 20 19 d7 d8 gnd mr len enecl v cce q0 q1 v cco q2 v cco q3 26 27 28 2 3 4 18 17 16 14 13 12 15 d5 d4 v cct d3 d2 d1 d0 q8 q7 v cco q6 v ee q5 q4 mc100h602fn plcc28 37 units/rail
mc10h602, mc100h602 http://onsemi.com 2 dc characteristics: v cct = 5.0 v 10%; v ee = 5.2 v 5% (10h version); v ee = 4.2 v to 5.5 v (100h version) 0 c 25 c 75 c symbol parameter min max min max min max unit condition power supply current i ee ecl 10h 100h 125 122 125 123 125 132 ma i cch i ccl ttl 48 50 48 50 48 50 ma ac characteristics: v cct = 5.0 v 10%; v ee = 5.2 v 5% (10h version); v ee = 4.2 v to 5.5 v (100h version) 0 c 25 c 75 c symbol parameter min max min max min max unit condition t plh t phl propagation delay to output d len mr enecl 1.4 2.0 2.0 1.6 3.0 3.4 3.4 3.2 1.5 2.1 2.1 1.7 3.2 3.5 3.5 3.3 1.7 2.4 2.5 1.8 3.5 3.7 3.9 3.7 ns t s setup time, d to len 2.0 2.0 2.0 ns t h hold time, d to len 1.0 1.0 1.0 ns t w (l) len pulse width, low 2.0 2.0 2.0 ns t r t f output rise/fall time 20% 80% 0.5 1.5 0.5 1.5 0.5 1.5 ns 10h ecl dc characteristics: v cct = 5.0 v 10%; v ee = 5.2 v 5% 0 c 25 c 75 c symbol parameter min max min max min max unit condition i inh i inl input high current input low current 0.5 225 0.5 145 0.5 145 m a m a v ih v il input high voltage input low voltage 1170 1950 840 1480 1130 1950 810 1480 1070 1950 735 1450 mv v oh v ol output high voltage output low voltage 1020 1950 840 1630 980 1950 810 1630 920 1950 735 1600 mv 50 w to 2.0 v 100h ecl dc characteristics: v cct = 5.0 v 10%; v ee = 4.2 v to 5.5 v 0 c 25 c 75 c symbol parameter min max min max min max unit condition i inh i inl input high current input low current 0.5 225 0.5 145 0.5 145 m a m a v ih v il input high voltage input low voltage 1165 1810 880 1475 1165 1810 880 1475 1165 1810 880 1475 mv v oh v ol output high voltage output low voltage 1025 1810 880 1620 1025 1810 880 1620 1025 1810 880 1620 mv 50 w to 2.0 v ttl dc characteristics: v cct = 5.0 v 10%; v ee = 5.2 v 5% (10h version); v ee = 4.2 v to 5.5 v (100h version) 0 c 25 c 75 c symbol parameter min max min max min max unit condition v ih v il input high voltage input low voltage 2.0 0.8 2.0 0.8 2.0 0.8 v v i ih input high current 20 100 20 100 20 100 m a v in = 2.7 v v in = 7.0 v i il input low current 0.6 0.6 0.6 ma v in = 0.5 v v ik input clamp voltage 1.2 1.2 1.2 v i in = 18 ma
mc10h602, mc100h602 http://onsemi.com 3 package dimensions plcc28 fn suffix plastic plcc package case 77602 issue d notes: 1. datums l, m, and n determined where top of lead shoulder exits plastic body at mold parting line. 2. dimension g1, true position to be measured at datum t, seating plane. 3. dimensions r and u do not include mold flash. allowable mold flash is 0.010 (0.250) per side. 4. dimensioning and tolerancing per ansi y14.5m, 1982. 5. controlling dimension: inch. 6. the package top may be smaller than the package bottom by up to 0.012 (0.300). dimensions r and u are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 7. dimension h does not include dambar protrusion or intrusion. the dambar protrusion(s) shall not cause the h dimension to be greater than 0.037 (0.940). the dambar intrusion(s) shall not cause the h dimension to be smaller than 0.025 (0.635). n m l v w d d y brk 28 1 view s s lm s 0.010 (0.250) n s t s lm m 0.007 (0.180) n s t 0.004 (0.100) g1 g j c z r e a seating plane s lm m 0.007 (0.180) n s t t b s lm s 0.010 (0.250) n s t s lm m 0.007 (0.180) n s t u s lm m 0.007 (0.180) n s t z g1 x view dd s lm m 0.007 (0.180) n s t k1 view s h k f s lm m 0.007 (0.180) n s t dim min max min max millimeters inches a 0.485 0.495 12.32 12.57 b 0.485 0.495 12.32 12.57 c 0.165 0.180 4.20 4.57 e 0.090 0.110 2.29 2.79 f 0.013 0.019 0.33 0.48 g 0.050 bsc 1.27 bsc h 0.026 0.032 0.66 0.81 j 0.020 0.51 k 0.025 0.64 r 0.450 0.456 11.43 11.58 u 0.450 0.456 11.43 11.58 v 0.042 0.048 1.07 1.21 w 0.042 0.048 1.07 1.21 x 0.042 0.056 1.07 1.42 y 0.020 0.50 z 2 10 2 10 g1 0.410 0.430 10.42 10.92 k1 0.040 1.02
mc10h602, mc100h602 http://onsemi.com 4 on semiconductor and are trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scill c data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent r ights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into t he body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. publication ordering information asia/pacific : ldc for on semiconductor asia support phone : 3036752121 (tuefri 9:00am to 1:00pm, hong kong time) toll free from hong kong 80044223781 email : onlitasia@hibbertco.com japan : on semiconductor, japan customer focus center 4321 nishigotanda, shinagawaku, tokyo, japan 1418549 phone : 81357402745 email : r14525@onsemi.com fax response line : 3036752167 8003443810 toll free usa/canada on semiconductor website: http://onsemi.com for additional information, please contact your local sales representative. mc10h602/d north america literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com n. american technical support : 8002829855 toll free usa/canada europe: ldc for on semiconductor european support german phone: (+1) 3033087140 (mf 2:30pm to 5:00pm munich time) email: onlitgerman@hibbertco.com french phone: (+1) 3033087141 (mf 2:30pm to 5:00pm toulouse time) email: onlitfrench@hibbertco.com english phone: (+1) 3033087142 (mf 1:30pm to 5:00pm uk time) email: onlit@hibbertco.com
|
